top of page
HOW TO VIDEOS AND CHIPPER MAINTENANCE
how to videos
OPERATION and safety
FEED CHUTE
Always stand to the side when feeding the chip chute
CHIP CHUTE
Stay clear of the chip chute at all times
Towing
3in offroad only 5, 6 and 7 inch are 45 mph, slow down on turns.
SAFETY BAR
Check the safety bar shutoff on every use to ensure your safety
DANGER
Never reach into the chutes when machine is running
Chutes open
Never run machine with the chutes open
TREES only
Machine is designed for Trees and Leaves only
WHEEL BRAKE
Set the wheel brake before operation of the machine
PROTECTION
Wear protective clothing, face, ear, eye and glove protection at all times
clear the area
Other persons in the area should be clear of the machine when running
cui
DO NOT CHIP UNDER THE INFLUENCE OF ALCOHOL OR DRUGS
towbar
Remember to follow these steps when towing:
1. Lock the towbar coupler before towing and connect the safety chains.
2. Ensure that the ball is fully inserted into the coupler.
3. If necessary, use the adjustment nut inside the coupler to adjust the ball locking flange.
4. Use a drop hitch if your truck is too high to ensure that the chipper tows level and prevents the toolbox from hitting the road on low spots.
front wheels
Raise the front wheels to horizontal before towing the 6 and 7 inch chippers.
ENGINE
ENGINE OIL
Use 10W30 MobilOne or equivalent
7hp - 212cc 0.6L
15hp - 500cc 1.1L
20hp - 740cc 1.6L
34hp - 999cc 2.4L
OIL CHANGE
After first 20 hours then 150 hours thereafter.
oil filter
SPARK PLUGS
GAS FILTER
AIR FILTER
Replace once per season or as needed
GASOLINE
High Grade 91 or better
HIGH ALTITUDE
7hp - 212cc Kit 1 = 3000-6000 Elev. Kit 2 = 6000-8000 Elev.
15hp - 500cc Kit 1 = 3000-6000 Elev. Kit 2 = 6000-8000 Elev.
20hp - 740cc Engine is pre-equipped with High Elevation
34hp - 999cc Engine is pre-equipped with High Elevation
TANK SHUT OFF
When not in use turn your gas valve OFF.
CHASSIS
BEARING GREASE
NLGI 3 grease is recommended for large bearings, cutting drum shaft bearings, high ambient temperatures and the presence of vibration.
AXLE GREASE
remove end cap - use NLGI 2 grade grease for sealed hub bearings
HARDWARE
Check all hardware regularly as vibration may loosen hardware.
tire pressure
Front Tires = 30PSI Rear Tires = 70PSI
HARDWARE
Check all hardware regularly as vibration may loosen hardware.
CHUTE LATCHES
Inspect all latches and pin lock when chutes are closed
toolbox
Inspect latch and pin lock when towing
cutting drum
blades
Flip reversable blade to new edge or replace when dull. DO NOT SHARPEN. Changing the cut angle and the cutting edge temper will reduce the performance of the tornatic machine and reduce blade life. Use ONLY OEM Blades available on Bigbear Power Parts Store. Always wear thick gloves when changing these razor sharp blades.
drum jams
Hey there! Just a friendly reminder to run the drum clean before turning off the machine. Make sure to clear out any chips and branches from the drum and feed chutes. If there are any stubborn jams, you remove the drum shaft cover and with the provided drum shaft tool turn the drum shaft counterclockwise to remove the chips. To help the chips slide out, you can spray some WD40 under the drum, but avoid using water as it can cause the chips to swell. Remenber to run the drum clean before shutdown and everything keeps running smoothly!
CUTTING ANVIL
Replacing and flipping blades requires no adjustment to the cutting anvil. In the event you replace the anvil, set the cutting gap to 1/16 inch before tightening all the anvil bolts.
bottom of page